Can You Repair A Cracked Retainer
Joined
·
334 Posts
Discussion Starter · #1 ·
Then, today I took out on of my graphics cards (I wasn't really utilizing it, and so I decided to sell it), and I had to exercise a little tube re-routing.
My reckoner was not congenital by me, I bought it as a complete organisation here off of OCN.
Whilst re-routing my tubes, I found that the way I had my reservoir oriented was causing me the problem. All I had to practice was use the other inlet - it is a tube reservoir with 2 inlets. I took my affront out of the top thread where it was, and then went to remove the metal "bolt" kind of thing:
I thought I had to just plough information technology with a penny or something. I tried to plough it (to the left ofc) and it wouldn't budge. Even with all my strength it wouldn't budge. And so I noticed cracks around the commodities-looking thing.
What can I do about these cracks? Will they leak? Practise I accept to supplant my reservoir? It would really suck if I would, because the only other compuer I have is my laptop, and I need the horsepower of my desktop.
My 2d question is this: what is the proper way to remove the bolt-looking affair? Was I doing it wrong?
My concluding question: can my loop operate without a reservoir for the time being? Can I just put a affront on of my pump where the reservoir was feeding it?
Thanks in accelerate for all your help,
-Scott
Joined
·
1,203 Posts
Quote:
Darn, based on the pics that were up there, I thought I had figured out the problem.
Joined
·
334 Posts
Discussion Starter · #3 ·
Quote:
Originally Posted by breenemeister
Darn, based on the pics that were upwardly in that location, I thought I had figured out the problem.
Ha ha. Yes those were my pictures I took yesterday for my university access card. It so happens that I had took four of them, and that I as well had four images in the folder from today.
The right film are now up, accept at em.
Joined
·
ii,884 Posts
If it hasnt leaked I wouldnt worry about it for now. Just replace it.
Joined
·
32,082 Posts
Use a scewdriver and make certain yous are twisting the right way. When replacing the cap, brand sure not to over tighten.
Those cracks probably won't leak, but may propagate over time. Yous could repair them, at least to a degree, with a estrus gun. You'd accept to be careful though, the amount temperature needed to repair modest cracks and the temperature at which you'll cause worse impairment are non far apart.
Joined
·
114 Posts
Looks similar it may have been overtightened by the previous owner, which got it stuck and caused the fractures.
If you lot can't unscrew it with a penny, become a wrench. If you can't unscrew it with a wrench, information technology is probably glued in
Every bit to the footling cracks, I'd go some transparent epoxy and put a thin layer over the surface of the reservoir, afterward removing the plug if possible. A rut gun / butane torch might work too, only it's easier to get information technology incorrect.
Joined
·
334 Posts
Word Starter · #seven ·
Thanks everyone for the suggestions. I will try to get it open with a wrench. If that doesn't work I will just remove the reservoir completely and run without it for the time being.
Joined
·
334 Posts
Give-and-take Starter · #8 ·
Mission successful:
At present to leak test the acrylic.
Joined
·
1,744 Posts
u can practise a layer of epoxy , and sand it downwardly
Joined
·
1,629 Posts
If it doesn't work out, I'm about to put i of those reservoirs in the forsale section cheap. Only used it for a couple days.
Joined
·
661 Posts
Joined
·
i,130 Posts
well outset i would torch it to get in bubbly then i would sand it down and uses epoxy so vitrify it but hey its non always successful
Joined
·
334 Posts
Discussion Starter · #xiii ·
Quote:
Originally Posted by Capt Proton
This
Hm, not a bad price. Have you whatsoever feel with it?
Joined
·
21,557 Posts
A couple drops of crazy gum is all y'all need. It will seep into the cracks sealing it.
Joined
·
334 Posts
Discussion Starter · #15 ·
Quote:
Originally Posted past tsm106
A couple drops of crazy glue is all you demand. Information technology will seep into the cracks sealing information technology.
That sounds more like the ghetto, no-toll solution I was looking for
Anyways, I didn't find whatever leaks - nosotros nowadays the sink method:
Just in case though I should probably put some crazy gum on there. Practice I just drop it on summit of the cracks? On the inside or outside?
Thanks.
Joined
·
21,557 Posts
It's not ghetto. That's how you speedily fix acrylic. Put some drops on the outside, let information technology dry out. Done.
Btw leak testing like that isn't very meaningful because there is no pressure. Once the loop o is filled and there is pressure, yous will know lol.
Joined
·
334 Posts
Word Starter · #17 ·
Quote:
Originally Posted by tsm106
It'south not ghetto. That's how y'all rapidly gear up acrylic. Put some drops on the exterior, let it dry. Washed.
Btw leak testing similar that isn't very meaningful considering there is no pressure. One time the loop o is filled and there is pressure, you will know lol.
Okay cheers for your advice. Doing information technology now.
Joined
·
6,238 Posts
Information technology will near probably wont leak as information technology is. Crazy glue wont hurt but then again I doubt is volition do much good either. I'd say use it for now simply start looking for a replacement only to exist safe.
Joined
·
21,557 Posts
If you lot have the original invoice, y'all could ship it back for rma and go a new one. Those things have gone thru more than a few revisions. That said most cracks are due to over-tightening.
Joined
·
334 Posts
Give-and-take Starter · #20 ·
Computer is running, no leaks. Have the case open on the tabular array beside me to lookout for things going bad. Thanks everybody.
Source: https://www.overclock.net/threads/can-you-repair-cracked-acrylic.1294675/
Posted by: garzashoutheasken.blogspot.com
0 Response to "Can You Repair A Cracked Retainer"
Post a Comment